AutomotiveWireless AudioUSBPower Over USB ControllersUSB to Ethernet ControllersUSB Graphics ControllersUSB HubsStandalone USB HubsUSB Hub CombosUSB Flash Media ControllersUSB Switches & Port Protection DevicesUSB TransceiversSecurityEthernet & Embedded NetworkingPC System & I/O ControllersThermal & Power ManagementCapacitive Touch Sensors
Categories
AutomotiveWireless AudioUSBSecurityEthernet & Embedded NetworkingPC System & I/O ControllersThermal & Power ManagementCapacitive Touch Sensors
Categories
Power Over USB ControllersUSB to Ethernet ControllersUSB Graphics ControllersUSB HubsUSB Flash Media ControllersUSB Switches & Port Protection DevicesUSB Transceivers
Categories
Standalone USB HubsUSB Hub Combos
Products
USB2422USB2532USB2533USB2534USB3503USB3613USB3803USB3813USB4604USB4624USB5434BUSB553xBUSB2412USB251xBUSB251xUSB2524USB82514
USB2502Buy Now!
Two-Port USB 2.0 Hub Controller
OverviewDescriptionApplicationsBlock DiagramOrderingDownload

Note: The USB2502 is not recommended for new designs. The USB2512 is the suggested replacement device for this product.

General Features

 

  • Compliant with USB 2.0 Specification
  • Hub Controller IC with Two Downstream Ports
  • Enables Bus-Powered Hi-Speed Hub Design
  • Default Configuration with Pin Selectable Options
  • Flexible OEM Configuration Options
  • 36 Pin QFN or 48 Pin TQFP lead-free RoHS compliant package

Hardware Features

  • Detects Removal of Self-Power and Automatically Changes Mode to Bus-Power
  • Integrated Termination and Pull-Up/Pull-Down Resistors
  • Internal Short Circuit Protection of DP and DM Lines
  • On-Chip Oscillator Uses Low Cost 24MHz Crystal
  • Supports Ganged Over-Current Protection and Power Control

OEM Selectable Features

The 2-Port Hub supports several OEM selectable features:

  • Customize Vendor ID, Product ID, and Device ID
  • Operation as a bus-powered, self-powered or dynamic-powered hub
    (When configured for dynamic operation, the controller automatically switches to bus-powered mode if a local power source is unavailable)
  • Select whether the hub is part of a compound device
    (When any downstream facing port is permanently hardwired to a USB peripheral device, the hub is part of a compound device)
  • Select the presence of a permanently hardwired USB peripheral device on a port by port basis
  • Configure the delay time for filtering the over-current sense inputs
  • Configure the delay time until port power is good after receiving command to turn on downstream port power
  • Indicate the maximum current that the 2-port hub consumes from an upstream port
  • Indicate the maximum current required for the hub controller

Pin Selectable Options for Default Configuration

  • Select Operation as Either a Bus-Powered Hub or a Self-Powered Hub
  • Select Downstream Port Power Control Polarity

 

Although the information in this document has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to product descriptions and specifications at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order. Products may contain design defects or errors known as anomalies which may cause a product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC and the SMSC logo are registered trademarks of Standard Microsystems Corporation ("SMSC"). Other names mentioned may be trademarks of their respective holders. All claims made herein speak as of the date of this material. The company does not undertake to update such statements.

Buy Now

Digi-Key:
www.digikey.com

Mouser Electronics:
www.mouser.com

Related Links

RoHS/Package Information

Parametric Search

Compare USB Hubs

Last Change: 06th of February 2013
SMSC ©2013 All rights reserved.
Privacy PolicySitemapLegalTrademarks